- Sensors
- Miniature Photoelectric Sensors
- Compact Photoelectric Sensors
- Midsize Photoelectric Sensors
- Fullsize Photoelectric Sensors
- Laser Sensors
- Ultrasonic Sensors
- Fiber Optic Sensors
- Part-Sensing Sensors
- Measuring Array Sensors
- Slot Sensors
- Analog Output
- L-GAGE Q50 Series—Analog
- L-GAGE LG5 and LG10 Series
- Analog OMNI-BEAM Series
- U-GAGE S18U Series—Analog
- L-GAGE LT3 Series
- U-GAGE QT50U DC Series—Analog
- U-GAGE T30U—Analog & Discrete
- A-GAGE EZ-ARRAY Series
- D10 Expert with Numeric Display—Analog & Discrete
- L-GAGE LT7 Series
- T-GAGE M18T Series—Analog
- A-GAGE MINI-ARRAY Series Controllers—Discrete/Analog Outputs
- QL55 Series
- U-GAGE T30UX: Analog
- U-GAGE Q45U Series—Analog
- U-GAGE ULTRA-BEAM Series—Analog
- U-GAGE Q45UR Series—Analog
- U-GAGE Sonic OMNI-BEAM Ultrasonic Sensors
- Optical Touch Button
- Temperature Sensors
- Vehicle Detection
- Radar Sensors
- Light Gauging Sensors
- Intrinsically Safe
- True Color Sensors
- Registration Mark Sensors
- Luminescence Sensors
- Remote Amplifier
- High-Pressure, Washdown Rated
- Sensors Accessories
- Machine Safety
- Vision Sensors and Vision Lighting
- Indicator Lights
- Wireless Sensor Networks
A-GAGE EZ-ARRAY Series
Uses & Applications
Overview
- Applications include edge and center-guiding, loop tension control, hole sizing, parts counting and on-the-fly product sizing and profiling.
- Closely spaced infrared beams detect objects as small as 5 mm wide; edge resolution is 2.5 mm.
- Controller functionality is built into the receiver, so basic setup requires no controller, software, or PC.
- Easy-to-use software is included for advanced configuration, using a PC.
- Configuration options include 14 measurement modes, three scanning methods, two analog and two discrete outputs and a serial output.
- Range is 4 meters.
- Array heights range from 150 to 2400 mm.
Product Specifications
| Supply Voltage (Limit Values) | Emitter:12 to 30V dc Receiver analog current models:12 to 30V dc Receiver analog voltage models:15 to 30V dc |
|---|---|
| Supply Power Requirements | Emitter/receiver pair:less than 9 W (exclusive of load) |
| Delay at Power-up | 2 seconds |
| Emitter/Receiver Range | 400 mm to 4 m |
| Field of View | Nominally ± 3° |
| Beam Spacing | 5 mm |
| Light Source | Infrared LED |
| Minimum Object Detection Size | Straight scan, low-contrast:5 mm Straight scan, high-excess-gain:10 mm Note:See quick start guide p/n 126701 for other scan mode values; size is tested using a rod. |
| Sensor Positional Resolution | Straight scan:5 mm Double-edge scan:2.5 mm Single-edge scan:2.5 mm |
| Teach Input (Receiver Gray Wire) | Low:0 to 2 V High:6 to 30 V or open (input impedance 22 K ohms) |
| Output Configuration | Two discrete output and two analog output
Discrete outputs:Solid-State NPN (current sinking) or PNP (current sourcing) Analog output:0 to 10V dc (voltage sourcing) or 4 to 20 mA (current sourcing) |
| Output Rating | Discrete output:100 mA max. each output OFF-state leakage current: NPN:less than 200 uA @ 30V dc
PNP:less than 10 uA @ 30V dc
ON-state saturation voltage:NPN:less than 1.6V @ 100 mA
PNP:less than 2.0V @ 100 mA
Analog voltage output:Maximum current load:5 mA
Analog current output:Maximum resistance load:(Vsupply–3) / 0.020
|
| Serial Communication Interface | EIA-485 Modbus RTU (up to 15 nodes per communication ring) RTU binary format Baud rate:9600, 19.2K or 38.4K, 8 Data Bits, 1 Stop Bit, and Even, Odd, or 2 Stop Bits and No Parity |
| Scan Time | Scan times depend on scan mode and sensor length. Straight scan times range from 2.8 to 26.5 milliseconds. |
| Status Indicators | Emitter:Red status indicators Red ON steady:status OK
Red flashing @ 1 hz:error
Receiver:7 Zone Indicators: Red:blocked channels within zone
Green:all channels clear within zone
3-digit 7-segment indicators:measurement mode / diagnostic informationSensor Status Bi-Color Indicator LED: Red:hardware error or marginal alignment
Green:OK
Modbus Activity Indicator LED:YellowModbus Error Indicator LED:Red |
| System Configuration | 6-position DIP switch:Used to set scanning type, measurement modes, analog slope and discrete output 2 function. Alternate software GUI interface provides additional options; see Section 1 and Section 5 of the full manual (p/n 130426). |
| Push Buttons (Receiver Interface) | Two momentary push buttons for alignment and gain level selection. |
| Connections | Serial communication:The receiver uses a PVC-jacketed, 5-conductor 22-gauge quick-disconnect cable, 5.4 mm diameter. QD cables are ordered separately. Other Sensor connections:8-conductor quick-disconnect cables (one each for emitter and receiver). Length may not exceed 75 meters long. PVC-jacketed cables measure 5.8 mm diameter, have shield wire; 22-gauge conductors. QD cables are ordered separately. |
| Construction | Aluminum housing with clear-anodized finish; acrylic lens cover |
| Environmental Rating | IEC IP65 |
| Operating Conditions | Temperature:–40° to +70° C Relative humidity:95% at 50° C (non-condensing) |
Banner Insider eNewsletter
Helpful application information, new product updates, answers to frequently asked questions, and more.
Subscribe Now »"No more costly wiring runs"
“I’m delighted with Banner’s SureCross wireless system. It gives us comprehensive monitoring and control in previously inaccessible locations. And it’s easy to expand and relocate as needed.”
Worldwide Distributors
Banner has more than 2,000 distributors worldwide — ready to help you.
Find international distributors