| Supply Voltage (Limit Values) | Emitter:12 to 30V dc Receiver analog current models:12 to 30V dc Receiver analog voltage models:15 to 30V dc |
|---|---|
| Supply Power Requirements | Emitter/receiver pair:less than 9 W (exclusive of load) |
| Delay at Power-up | 2 seconds |
| Emitter/Receiver Range | 400 mm to 4 m |
| Field of View | Nominally ± 3° |
| Beam Spacing | 5 mm |
| Light Source | Infrared LED |
| Minimum Object Detection Size | Straight scan, low-contrast:5 mm Straight scan, high-excess-gain:10 mm Note:See quick start guide p/n 126701 for other scan mode values; size is tested using a rod. |
| Sensor Positional Resolution | Straight scan:5 mm Double-edge scan:2.5 mm Single-edge scan:2.5 mm |
| Teach Input (Receiver Gray Wire) | Low:0 to 2 V High:6 to 30 V or open (input impedance 22 K ohms) |
| Output Configuration | Two discrete output and two analog output
Discrete outputs:Solid-State NPN (current sinking) or PNP (current sourcing) Analog output:0 to 10V dc (voltage sourcing) or 4 to 20 mA (current sourcing) |
| Output Rating | Discrete output:100 mA max. each output OFF-state leakage current: NPN:less than 200 uA @ 30V dc
PNP:less than 10 uA @ 30V dc
ON-state saturation voltage:NPN:less than 1.6V @ 100 mA
PNP:less than 2.0V @ 100 mA
Analog voltage output:Maximum current load:5 mA
Analog current output:Maximum resistance load:(Vsupply–3) / 0.020
|
| Serial Communication Interface | EIA-485 Modbus RTU (up to 15 nodes per communication ring) RTU binary format Baud rate:9600, 19.2K or 38.4K, 8 Data Bits, 1 Stop Bit, and Even, Odd, or 2 Stop Bits and No Parity |
| Scan Time | Scan times depend on scan mode and sensor length. Straight scan times range from 2.8 to 26.5 milliseconds. |
| Status Indicators | Emitter:Red status indicators Red ON steady:status OK
Red flashing @ 1 hz:error
Receiver:7 Zone Indicators: Red:blocked channels within zone
Green:all channels clear within zone
3-digit 7-segment indicators:measurement mode / diagnostic informationSensor Status Bi-Color Indicator LED: Red:hardware error or marginal alignment
Green:OK
Modbus Activity Indicator LED:YellowModbus Error Indicator LED:Red |
| System Configuration | 6-position DIP switch:Used to set scanning type, measurement modes, analog slope and discrete output 2 function. Alternate software GUI interface provides additional options; see Section 1 and Section 5 of the full manual (p/n 130426). |
| Push Buttons (Receiver Interface) | Two momentary push buttons for alignment and gain level selection. |
| Connections | Serial communication:The receiver uses a PVC-jacketed, 5-conductor 22-gauge quick-disconnect cable, 5.4 mm diameter. QD cables are ordered separately. Other Sensor connections:8-conductor quick-disconnect cables (one each for emitter and receiver). Length may not exceed 75 meters long. PVC-jacketed cables measure 5.8 mm diameter, have shield wire; 22-gauge conductors. QD cables are ordered separately. |
| Construction | Aluminum housing with clear-anodized finish; acrylic lens cover |
| Environmental Rating | IEC IP65 |
| Operating Conditions | Temperature:–40° to +70° C Relative humidity:95% at 50° C (non-condensing) |
Helpful application information, new product updates, answers to frequently asked questions, and more.
Subscribe Now »The source for all Banner product lines. Features multiple navigation options, applications and product comparisons, and detailed specifications for brackets, cordsets and other accessories.
Get it Now »Banner has more than 2,000 distributors worldwide — ready to help you. Enter a U.S. zip code