SureCross DX70 Wireless Modules
Overview
SureCross DX70 wireless networks utilize binding technology to ensure that a Node communicates only with its corresponding Gateway without noise obstruction or signal interference.
- Open design supports inputs from sensors and devices made by Banner and other manufacturers
- Supports digital and analog I/O in a single unit
- Combines Frequency Hopping Spread Spectrum (FHSS) and Time Division Multiple Access (TDMA) architecture to ensure reliable data delivery
- IEC IP67, NEMA 6 rated housing for long-lasting performance in rugged environments
- Input-to-output mapping is controlled by a factory-configured Gateway
- Available in 900 MHz or 2.4 GHz frequency models to accommodate worldwide communication standards
Product Specifications
| General | Power:+10 to 30V dc Power consumption:less than 1.4 W @ 24V dc Indicators:Green Power ON LED, Yellow Signal Strength LED Mounting:#10 or M5 (M5 hardware included) M5 fasteners—max. tightening torque:0.56 N/m (5 in/lbf) Case material:polycarbonate Weight:0.26 kg External cable gland:one 1/2—NPT type Cable glands, max. tightening torque:0.56 N/m (5 in/lbf) |
|---|---|
| Radio | Range with standard 2 dB antenna*: 900 MHz models:up to 4.8 km (3 miles)
2.4 GHz models:up to 3.2 km (2 miles)
Frequency:900 MHz models::902 -928 MHz ISM band
2.4 MHz models:2.4 - 2.4835 GHz ISM band
Transmit power:900 MHz models:21 dBm conducted
2.4 GHz models:18 dBm conducted, 20 dBm EIRP max.
Spread spectrum technology:Frequency Hopping Spread Spectrum (FHSS)Antenna connector:ext. reverse polarity SMA - 50 ohms Antenna—max. tightening torque:0.45 N/m (4 in/lbf) Link timeout:8 seconds *Note:The range depends upon the environment and line of site. High-gain antennas are available to increase the range. |
| Inputs | Discrete:four sourcing (or sinking) Rating:3 mA max. current @ 30V dc
Sample rate:62 milliseconds
Report rate:On Change of State
ON condition:greater than 8V (less than 0.7V for sinking)
OFF condition:less than 5V (greater than 2V or Open for sinking)
Analog:two, 0 to 20 mASample rate:62 milliseconds
Report rate:1 second or on Change of State (1% change in value)
Accuracy:0.1% of full scale +0.01% per °C
|
| Outputs | Discrete:four sourcing Rating:100 mA max. current @ 30V dc
ON condition:supply minus 2V
OFF condition:less than 2V
Analog:two, 0 to 20 mAMax. end-to-end Latency*:400 milliseconds
Output state following timeout:programmed by dip switch
*Note:from the sample point and with a good RF signal |
| Environmental | Environmental rating*:IEC IP67; NEMA 6 Operating temperature**:-40 to +85° C (electronics); -20 to +80° C (LCD) Relative humidity:95% (non-condensing) Shock and vibration:IEC IEC 68-2-6 and IEC 68-2-7 Shock:30 g, 11 millisecond half-sine wave, 18 shocks
Vibration:0.5 mm p-p, 10-60 Hz
*Note:Operating the devices at the maximum operating conditions for extended periods can shorten the life of the device. |
| Compliance | 900 MHz models:FCC ID TGUDX80 - This device complies with FCC Part 15, Subpart C, 15.247 2.4 GHz models:FCC ID UE300DX80-2400 - This device complies with FCC Part 15, Subpart C, 15.247. ETSI/EN: In accordance with EN 300 328: V1.7.1 (2006-05) |
| Product Specifications and Modifications Disclaimer | All specifications published in this document are subject to change. Banner reserves the right to modify the specifications of products, prior to their order, without notice. |
Banner Insider eNewsletter
Helpful application information, new product updates, answers to frequently asked questions, and more.
Subscribe Now »Worldwide Distributors
Banner has more than 2,000 distributors worldwide — ready to help you.
Find international distributors