FlexPower Nodes

The FlexPower Nodes are slave devices for Banner's wireless sensor network, but can be powered by 10-30V dc, 3.6V Lithium D cell batteries, or solar power. FlexPower Nodes with batteries integrated into the housing can only be powered from the integrated battery. FlexPower Nodes are available with discrete I/O, analog I/O, a mix of discrete and analog I/O, and with special instrumentation configurations.

Models ending in C use external terminal blocks instead of internal terminal blocks. These C models are Class I, Division 2 certified when installed in a suitable enclosure. Certifications are listed on the Classified Areas page.

For a basic description of how antennas work, how to connect a remote antenna system, and the differences between omni and Yagi antennas, refer to Antenna Basics.


	The standard IP67 base with internal terminal blocks	The low-profile IP20 base with external terminal blocks.

Discrete I/O

Model	Frequency	Base	I/O	Data Sheet
DX80N9X2S4N4	900 MHz	IP67	Discrete: Four selectable inputs, four NMOS sinking outputs Power Outputs: Two (constant power)	136328
DX80N9X2S4N4C	900 MHz	IP20
DX80N2X2S4N4	2.4 GHz	IP67
DX80N2X2S4N4C	2.4 GHz	IP20

Discrete and Analog I/O

Model	Frequency	Base	I/O	Data Sheet
DX80N9X2S2N2M2	900 MHz	IP67	Discrete: Two selectable inputs, two NMOS sinking outputs Analog: Two 0-20 mA inputs (depending on configuration) Switch Power Outputs: Two	131296
DX80N9X2S2N2M2C		IP20
DX80N2X2S2N2M2	2.4 GHz	IP67
DX80N2X2S2N2M2C		IP20
DX80N9X2S2N2V2	900 MHz	IP67	Discrete: Two selectable inputs, two NMOS sinking outputs Analog: Two 0-10V inputs (depending on configuration) Switch Power Outputs: Two
DX80N9X2S2N2V2C		IP20
DX80N2X2S2N2V2	2.4 GHz	IP67
DX80N2X2S2N2V2C		IP20
DX80N9X1S2N1M1	900 MHz	IP67, integrated battery	Discrete: Two selectable inputs, one NMOS sinking outputs Analog: One 0-20 mA input (Battery powered only)	147502
DX80N2X1S2N1M1	2.4 GHz
DX80N9X1S2N1V1	900 MHz		Discrete: Two selectable inputs, one NMOS sinking outputs Analog: One 0-10V input (Battery powered only)
DX80N2X1S2N1V1	2.4 GHz
DX80N9X2S2N2M4	900 MHz	IP67	Discrete: Two selectable inputs, two NMOS sinking outputs Analog: Four inputs (0-20 mA or 4-20 mA, depending on configuration)	131762
DX80N9X2S2N2M4C		IP20
DX80N2X2S2N2M4	2.4 GHz	IP67
DX80N2X2S2N2M4C		IP20
DX80N9X2S2N2V4	900 MHz	IP67	Discrete: Two selectable inputs, two NMOS sinking outputs Analog: Four inputs (0-10V)
DX80N9X2S2N2V4C		IP20
DX80N2X2S2N2V4	2.4 GHz	IP67
DX80N2X2S2N2V4C		IP20
DX80N9X2S4A2	900 MHz	IP67	Discrete: Two selectable inputs, two NMOS sinking outputs Counter: Two selectable inputs	136348
DX80N9X2S4A2C		IP20
DX80N2X2S4A2	2.4 GHz	IP67
DX80N2X2S4A2C		IP20
DX80N9X1S2A1	900 MHz	IP67, integrated battery	Discrete: One selectable input, one NMOS sinking output Counter: Two selectable inputs (Battery powered only)	136972
DX80N2X1S2A1	2.4 GHz
DX80N9X2S-CS1	900 MHz	IP67	Discrete: Two selectable inputs, one NMOS sinking output Analog: Two inputs (0-20 mA or 4-20 mA, depending on configuration) Switch Power: Continuous Thermistor: One input Battery Status: One (Supplies continuous courtesy power)	140373
DX80N2X2S-CS1	2.4 GHz

Temperature I/O

Model	Frequency	Base	I/O	Data Sheet
DX80N9X2S2N2T	900 MHz	IP67	Thermocouple: Three inputs, one thermistor CJC input Discrete: Two selectable inputs, two NMOS sinking outputs	131297
DX80N9X2S2N2TC	900 MHz	IP20
DX80N2X2S2N2T	2.4 GHz	IP67
DX80N2X2S2N2TC	2.4 GHz	IP20
DX80N9X2S0P0R	900 MHz	IP67	RTD: Four three-wire inputs	131597
DX80N9X2S0P0RC	900 MHz	IP20
DX80N2X2S0P0R	2.4 GHz	IP67
DX80N2X2S0P0RC	2.4 GHz	IP20

Counter I/O

Model	Frequency	Base	I/O	Data Sheet
DX80N9X2S4A2	900 MHz	IP67	Discrete: Two selectable inputs, two NMOS sinking outputs Counter: Two selectable inputs	136348
DX80N9X2S4A2C	900 MHz	IP20
DX80N2X2S4A2	2.4 GHz	IP67
DX80N2X2S4A2C	2.4 GHz	IP20
DX80N9X1S2A1	900 MHz	IP67, integrated battery	Discrete: One selectable input, one NMOS sinking output Counter: Two selectable inputs (Battery powered only)	136972
DX80N2X1S2A1	2.4 GHz	IP67, integrated battery		136972

To order the internal antenna models, replace the "S" in the 9th digit with a "W." Internal antennas require an additional week for manufacture and shipping. For example, DX80N9X2S4N4 is the model number for the external antenna device and DX80N9X2W4N4 is the internal antenna device. The -CS1 Nodes are not available with the internal antenna.

Models with batteries integrated into the housing are so noted. For all other FlexPower models, the DX81 or DX81P6 Battery Supply Modules must be ordered separately to power these devices from battery.

M-GAGE

The M-GAGE Nodes detect the presence or absence of vehicles and are powered by a 3.6V lithium D cell integrated into the housing.


	A compact round housing for easy burial installation

Model	Frequency	Base	I/O	Data Sheet
DX80N9X1W0P0ZR	900 MHz	Round	M-GAGE sensor with an internal antenna and a battery integrated into a compact, round housing	147116
DX80N2X1W0P0ZR	2.4 GHz	Round		147116

The M-GAGE Nodes are only available with an internal antenna.

FlexPower Node for Banner Serial FlexSensors


	Standard FlexPower base	Battery integrated into the housing

Model	Frequency	Base	I/O	Data Sheet
DX80N9X2S2S	900 MHz	Standard	One serial port to handle up to two serial FlexSensors.	136971
DX80N2X2S2S	2.4 GHz
DX80N9X1S1S	900 MHz	Integrated Battery	One serial port to handle one FlexSensor. (Battery powered only)	137322
DX80N2X1S1S	2.4 GHz

To order the internal antenna models, replace the "S" in the 9th digit with a "W." Internal antennas require an additional week for manufacture and shipping. For example, DX80N9X2S1S is the model number for the external antenna device and DX80N9X2W1S is the internal antenna device.

Banner

SureCross

Wireless Products