How To Set Up Muting with the LS Safety Light Curtain

Learn how to set-up the XS safety controller to work with a mute arm kit and LS safety light curtain. Banner’s pre-assembled mute arm kits are available in L, T and X configurations as a plug-n-play solution for end of line packaging applications.

Learn More About Safety Solutions

Barrières immatérielles de sécurité robustes de type 4 aux fonctionnalités très complètes de la série LS
Systèmes robustes de type 4 aux fonctionnalités très complètes de la série LS

Modèles intuitifs et simples à utiliser, dotés d'un large éventail de fonctionnalités et déclinés en plusieurs résolutions (14, 23 et 40 mm) et plusieurs longueurs (jusqu'à 1820 mm), sans angle mort. Indicateurs d'alignement très visibles et diagnostic intuitif pour simplifier l'installation et apporter aux constructeurs de machines une valeur ajoutée afin de satisfaire un large éventail de besoins.

Read More

Transcript

Banner’s pre-assembled Mute Arm Kits are available in L, T and X configurations as a plug-n-play solution for end of line packaging applications.

You can now use these mute arm kits with Banner EZ SCREEN LS Safety Light Curtains through the use of the XS safety controller.

Banner offers accessories to make mounting and electrical connection a breeze.

In this video will show you how to set-up the XS safety controller to work with the Mute Arm Kits, it’s really simple…

Add a safety light curtain

Add a mute sensor pair

The only trick here is you have to select Dual-Chanel PNP

In the functional View tab to create the configuration

Add a muting function block

If you have an L-Configuration use the one on the top left (maybe add a visual showing L, T and X configurations)

If you have a T or X Configuration use the one on the top right

There are a few advanced features as well

Mute enable

Mute time limit

And End Delay Time limit can be set for L-configurations

Add a latch reset function block and a latch reset

Use a physical manual reset button or use the virtual reset from an HMI.

Add a status output for the mute light.

In simulation mode we will test the configuration

First we test the safety light curtain and latch reset with mute off.

Next, lets test the mute function.

When enabled, a function block is purple with a 3 second count-down timer. Also, the status output for the mute light changes to green

After 3 seconds the status output and mute function turn off.

Try again an ensure the safety light curtain is muted…success!

The wiring diagram describes the wiring connections

Finally, select your industrial ethernet protocol, auto configure and the controller is now set-up up to talk to the PLC.

Visit bannerengineering.com to view the plug-n-play accessories to complete this set-up.Banner’s pre-assembled Mute Arm Kits are available in L, T and X configurations as a plug-n-play solution for end of line packaging applications.

You can now use these mute arm kits with Banner EZ SCREEN LS Safety Light Curtains through the use of the XS safety controller.

Banner offers accessories to make mounting and electrical connection a breeze.

In this video will show you how to set-up the XS safety controller to work with the Mute Arm Kits, it’s really simple…

Add a safety light curtain

Add a mute sensor pair

The only trick here is you have to select Dual-Chanel PNP

In the functional View tab to create the configuration

Add a muting function block

If you have an L-Configuration use the one on the top left (maybe add a visual showing L, T and X configurations)

If you have a T or X Configuration use the one on the top right

There are a few advanced features as well

Mute enable

Mute time limit

And End Delay Time limit can be set for L-configurations

Add a latch reset function block and a latch reset

Use a physical manual reset button or use the virtual reset from an HMI.

Add a status output for the mute light.

In simulation mode we will test the configuration

First we test the safety light curtain and latch reset with mute off.

Next, lets test the mute function.

When enabled, a function block is purple with a 3 second count-down timer. Also, the status output for the mute light changes to green

After 3 seconds the status output and mute function turn off.

Try again an ensure the safety light curtain is muted…success!

The wiring diagram describes the wiring connections

Finally, select your industrial ethernet protocol, auto configure and the controller is now set-up up to talk to the PLC.

Visit bannerengineering.com to view the plug-n-play accessories to complete this set-up.