모든 농업 솔루션
-
위험 지역의 모터 및 베어링 온도 모니터링
위험 지역의 모터 및 베어링 온도 모니터링
Banner의 DX99 노드는 써모커플 또는 RTD를 사용하여 모터 베어링의 온도를 모니터링하는 솔루션을 제공합니다. 저전력 센서 및 무선이기 때문에 최대 3년간 배터리 사용이 가능합니다. 이 노드는 기록 및 분석하기 위해 온도 데이터를 중앙 제어 위치로 다시 무선으로 보냅니다. 베어링 온도가 예기치 않게 올라가면 모터가 타거나 장비가 손상되기 전에 유지 보수를 예약할 수 있습니다. 이 온도 데이터는 어려움과 위험 때문에 무선 기술 없이는 모니터링되지 않을 수 있습니다.
-
크랜베리 소택지의 서리 방지 및 토양 수분 조절
크랜베리 소택지의 서리 방지 및 토양 수분 조절
토양 수분과 공기 온도 감지 범위는 일반적으로 1마일 미만이지만 현장 조사에서는 신호를 2마일까지 테스트했습니다. 멀티홉 무선과 안테나를 매우 낮은 곳에 설치한 상태에서 통신 범위를 최대화하기 위해 대형 무지향성 안테나와 마스터 무선을 설치했습니다.
-
온실 온도 및 습도 모니터링
온실 온도 및 습도 모니터링
온도 및 습도 센서에 직접 연결된 내부 배터리가 장착된 SureCross FlexPower™ 노드는 값 비싼 도관이나 케이블 없이 이러한 측정을 제공할 수 있으므로 여러 센서 위치에서 수동으로 데이터를 수집할 필요가 없습니다. 이 제품은 IP67 전자 제품으로 다양한 필터 옵션이 있어 온실에서 접하게 되는 폭넓은 온도 및 습도 범위에 적합합니다.
-
무선 네트워크를 이용한 냉동 시스템 모니터링
무선 네트워크를 이용한 냉동 시스템 모니터링
저항 온도 감지기가 워크인(출입식) 쿨러의 온도를 감지하고 데이터를 SureCross FlexPower 노드로 전송합니다. 이 노드는 해당 데이터를 다시 게이트웨이로 보내고 게이트웨이는 온도가 허용 한계를 초과하면 관리부서에 경보를 보냅니다. DX80 FlexPower 노드는 혹독한 환경에서 사용할 수 있도록 IP67 등급을 받았으며 추운 곳에서도 잘 작동합니다.
-
퇴비화 중 온도 모니터링
퇴비화 중 온도 모니터링
건초 더미 안에서 자동으로 온도를 모니터링하는 두 개의 열전대가 장착된 SureCross FlexPower™ 노드를 사용하면 수동으로 데이터를 수집할 필요가 없습니다.
-
호퍼의 마른 재료 충전 높이
호퍼의 마른 재료 충전 높이
호퍼 위에 장착된 L-GAGE LT3 레이저 거리 측정 센서는 재료의 불규칙한 표면까지의 거리를 측정하여 PLC를 통해 용기의 충전 높이을 계산할 수 있도록 합니다.
-
Large Vehicle Detection at an Outdoor Loading Dock
Large Vehicle Detection at an Outdoor Loading Dock
Wireless solution to detect presence of vehicle using a long sensing range.
-
Monitoring Railcar Wheels Wirelessly
Monitoring Railcar Wheels Wirelessly
Detect the railcar wheels and trigger an axle pushing arm wirelessly.
-
Gravity Irrigation with Pump and Flow Control [Success Story]
Gravity Irrigation with Pump and Flow Control [Success Story]
The Gateway, or wireless network controller, monitors the water level inside the water tank. When the water level drops, a Node installed with the reservoir pumps uses its outputs to cycle the pumps on or off. A series of Nodes monitors the amount of water flowing into each orchard. A 1 Watt Data Radio connected to the Gateway transmits the data to a mobile asset or a centralized control center for data processing and billing.
-
Center Pivot Irrigation
Center Pivot Irrigation
Center arm pivot irrigation systems are used throughout the Midwest to minimize water use and ensure crop health. Because the sections of the center pivot assembly have to move at different speeds, the motors moving each section must be monitored to verify each section is moving at the proper speed and time.
-
Outdoor Log Debarking
Outdoor Log Debarking
In the event of a problem or potential equipment damage, anyone along the length of the rope pull cable (up to 75 meters) can pull the cable or press the built-in E-stop button and stop the operation of the machine. The switch is ruggedly built, to allow for outdoor mounting even in inclement conditions. It provides visible rope tension indication and an auxiliary output for remote tension monitoring.
-
Debarking Control
Debarking Control
As a log moves toward the debarker, an EZ‑ARRAY receiver determines the total number of beams that are blocked. It sends an analog signal to the debarking station logic controller, which determines the diameter of the log and adjusts the log grippers and debarking blades to the log’s size. Accurately determining the log's size provides process stability and prevents damage to the debarking machine.
-
Controlling Pivot Irrigation [Success Story]
Controlling Pivot Irrigation [Success Story]
A municipality has over 30 farm fields irrigated with gray water using pivot irrigation systems. Local regulations prohibit the irrigation system from spraying over roads and ditches. The customer needs a solution that can reliably control the water flow to the end nozzle based on predetermined location coordinates.