How To Set Up Muting with the LS Safety Light Curtain

Learn how to set-up the XS safety controller to work with a mute arm kit and LS safety light curtain. Banner’s pre-assembled mute arm kits are available in L, T and X configurations as a plug-n-play solution for end of line packaging applications.

Learn More About Safety Solutions

Bauform LS – Typ-4-Sicherheits-Lichtvorhänge mit röhrenförmigem Gehäuse
Bauform LS – Typ-4-Sicherheits-Lichtvorhänge mit röhrenförmigem Gehäuse

Intuitives, benutzerfreundliches, funktionsreiches Modell mit einer Auflösung von 23 mm in einem vollwertigen Design ohne Blindzone. Erhältlich in 7 Schutzfeldhöhen von 280 bis 1050 mm in einem hygienischen röhrenförmigen 70 mm Gehäuse nach IP69 mit wasserabweisenden Belüftungsöffnungen zur Vermeidung von Kondensation.

Read More
Bauform LS − Muting-Arm-Kits
Bauform LS − Muting-Arm-Kits

Mit den Muting-Arm-Kits der Bauform LS kann jede Anwendung, die eine Finger- oder Handerkennung erfordert, problemlos mit Muting-Funktionen ausgestattet werden. Sie kombinieren vormontierte Plug-and-Play-Hardware mit Q20 Reflexionslichtschranken und reflektierenden Zielobjekten. Sie sind für die Verwendung mit LS-Sicherheits-Lichtvorhängen mit 14, 23 oder 40 mm Auflösung und SC/XS26-Sicherheitskontrollern konzipiert.

Read More

Transcript

Banner’s pre-assembled Mute Arm Kits are available in L, T and X configurations as a plug-n-play solution for end of line packaging applications.

You can now use these mute arm kits with Banner EZ SCREEN LS Safety Light Curtains through the use of the XS safety controller.

Banner offers accessories to make mounting and electrical connection a breeze.

In this video will show you how to set-up the XS safety controller to work with the Mute Arm Kits, it’s really simple…

Add a safety light curtain

Add a mute sensor pair

The only trick here is you have to select Dual-Chanel PNP

In the functional View tab to create the configuration

Add a muting function block

If you have an L-Configuration use the one on the top left (maybe add a visual showing L, T and X configurations)

If you have a T or X Configuration use the one on the top right

There are a few advanced features as well

Mute enable

Mute time limit

And End Delay Time limit can be set for L-configurations

Add a latch reset function block and a latch reset

Use a physical manual reset button or use the virtual reset from an HMI.

Add a status output for the mute light.

In simulation mode we will test the configuration

First we test the safety light curtain and latch reset with mute off.

Next, lets test the mute function.

When enabled, a function block is purple with a 3 second count-down timer. Also, the status output for the mute light changes to green

After 3 seconds the status output and mute function turn off.

Try again an ensure the safety light curtain is muted…success!

The wiring diagram describes the wiring connections

Finally, select your industrial ethernet protocol, auto configure and the controller is now set-up up to talk to the PLC.

Visit bannerengineering.com to view the plug-n-play accessories to complete this set-up.Banner’s pre-assembled Mute Arm Kits are available in L, T and X configurations as a plug-n-play solution for end of line packaging applications.

You can now use these mute arm kits with Banner EZ SCREEN LS Safety Light Curtains through the use of the XS safety controller.

Banner offers accessories to make mounting and electrical connection a breeze.

In this video will show you how to set-up the XS safety controller to work with the Mute Arm Kits, it’s really simple…

Add a safety light curtain

Add a mute sensor pair

The only trick here is you have to select Dual-Chanel PNP

In the functional View tab to create the configuration

Add a muting function block

If you have an L-Configuration use the one on the top left (maybe add a visual showing L, T and X configurations)

If you have a T or X Configuration use the one on the top right

There are a few advanced features as well

Mute enable

Mute time limit

And End Delay Time limit can be set for L-configurations

Add a latch reset function block and a latch reset

Use a physical manual reset button or use the virtual reset from an HMI.

Add a status output for the mute light.

In simulation mode we will test the configuration

First we test the safety light curtain and latch reset with mute off.

Next, lets test the mute function.

When enabled, a function block is purple with a 3 second count-down timer. Also, the status output for the mute light changes to green

After 3 seconds the status output and mute function turn off.

Try again an ensure the safety light curtain is muted…success!

The wiring diagram describes the wiring connections

Finally, select your industrial ethernet protocol, auto configure and the controller is now set-up up to talk to the PLC.

Visit bannerengineering.com to view the plug-n-play accessories to complete this set-up.

Zu Meine Bibliothek hinzufügen
Hinzugefügt